Fundamental Plumbing Insights for Bathtub Installation
Fundamental Plumbing Insights for Bathtub Installation
Blog Article
The article author is making a few good points regarding How to Install a Bathtub Yourself in general in this article further down.
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is also a reasonably hard job. If the old tub is conveniently accessible, the project can move speedily; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. See to it you have actually qualified on your own for the work and also are comfortable attempting it. Instead of working with a specialist to take over a halfway-completed task, it is far better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will assist you mount a brand-new bathtub in your bathroom if you have already acquired a new tub and also do not require to change the arrangement of your previous supply of water pipes.
Your tools and also product list should comprise the following:
Preparing for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome as a result of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using both wooden boards under its feet, position the bathtub in the required setting. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the tub till the level reads degree.
To set up faucets, fit all-time low of the outermost versatile faucet adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait till the bathtub has been made use of a minimum of once as this will resolve it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet and the sink. Protect the tap in place with the supplier supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap adapters. The previous type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath as well as the tiling, leading to difficulties with moisture and also possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can fracture fairly early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a friend on another site. Make sure you take the opportunity to share this blog posting if you enjoyed it. Kudos for your time. Come back soon.
Dial, and relax! Report this page